ESC50014 Short cased axial flow extract fan also know as ZAC500-41

Systemair, Vent-Axia, Ziehl-Abegg,

ESC50014 Short cased axial flow extract fan also know as ZAC500-41
ESC50014 Short cased axial flow extract fan also know as ZAC500-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

  • Supplied fully assembled
  • Fully speed controllable
  • Can be used in any non hazardous environment
  • Suitable to run in temperatures from ‑40°C to up to 70°C in some instances
  • Low to medium air volumes
  • Low to medium static pressures
  • Available sizes 315mm – 630mm from stock
  • 710mm – 1000mm check for availability
  • Tough epoxy paint finish
  • Die cast aluminium impellers (the bit that goes around)
  • Motor class F insulation with protection to IP54
  • All fans reversible for supply or extract

The curve below shows the fans performance, which is 2.1 m³/​s at Free Air and peaks at 1.4 m³/​s at 100Pa, the fan can perform anywhere between these points and the red dot is shown as an example

  • 66dB(A) at 1.5 metres from the listener
  • 59dB(A) @ 3 metres from the listener

Prices & Options
Code & Description Price  
esc50014 : ESC50014 Short cased axial flow extract fan also know as ZAC500-41 £351.11 + VAT £421.33
We accept : Visa, MasterCard, Maestro & PayPal


Related Products
ME1.3 Speed Controller by Flakt Woods
£47.00

ME1.3 Speed Controller by Flakt Woods

The Flakt Woods genuine range of ME Electronic fan speed controllers. This range of fan speed controllers is our best selling and can be used with any Fan / Motor which is single phase – 240 volts and fan speed controllable using either 2 or 3 wire control (+earth). ME1.1 suitable for a maximum full load of 1 a ...

500mm Louvre Shutter
£119.47

500mm Louvre Shutter

A Louvre Shutter is a gravity type shutter which can be used to terminate and weather extract systems. When the fan is running the plastic blades will open allowing the air to be extracted from the system, and when the fan is not running will be closed, this helps to prevent back draughts and water ingress The shutter is commonly used to terminate  ...

NCSP Gas Ventilation Interlock Panel
£176.00

NCSP Gas Ventilation Interlock Panel

NCSP Ventilation Gas interlock Panel This is our cheapest and best selling Ventilation Gas Interlock Panel The panel is designed to protect Kitchen staff from the dangers of Co2 fumes created when gas is used for cooking. It protects the staff by closing the Gas valve supplying t ...

A.V.Mount (Anti Vibration Mount)
£14.44

A.V.Mount (Anti Vibration Mount) – Load range per mount 9Kg — 50Kg

Supplied in sets of 4 Anti Vibration Mounts (A.V. Mounts) attach to the bottom of Mounting Feet. A.V. Mounts are used to isolate the fan from the system to prevent vibration transfer through fixings or structures. A.V. Mounts can be used to isolate any products from the main system to prevent vibration transfer The main uses we ...

A.V. Mounts (Anti Vibration Mounts)
£14.44

A.V. Mounts (Anti Vibration Mounts) – load range per mount 5Kg ‑28Kg

Supplied in sets of 4 Anti Vibration Mounts (A.V. Mounts) attach to the bottom of Mounting Feet. A.V. Mounts are used to isolate the fan from the system to prevent vibration transfer through fixings or structures. A.V. Mounts can be used to isolate any products from the main system to prevent vibration transfer The main uses we ...

500mm Flexible Connection
£37.70

500mm Flexible Connection

500mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting. A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures. It can also be used to simplify installation by bridging any small gaps b ...

500mm Mounting Feet
£28.42

500mm Mounting Feet

Supplied in pairs 500mm Mounting Foot, used to fit directly to the fan as part of a full ancillary package The Mounting Foot can be used to mount the fan in the horizontal or vertical position Usually used in conjunction with Anti Vibration Mounts Can also be used to fit directly to Silencers with or without Anti Vibration Moun ...

500mm dia Flange
£37.40

500mm dia Flange

500mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting Can also be used to fix directly to a Silencer Can also be used to fix directly to ducting Hot dipped Galvanised after manufacture

CDA 500 x 1D straight through Silencer
£225.74

CDA 5001D straight through Silencer

500mm dia x 500mm long straight through silencer (generally reduces a fan noise level by 7 – 10dB (A)* Can be supplied to either bolt directly to any manufacturer of cased axial or with spigots to mount inline with ducting. The addition of this silencer to a system will act in the same way a silencer does on a car, so if you’ve ever heard a car with  ...

500mm dia Flange
£22.37

500mm dia Flange – suits any manufacturer of fans

500mm dia Flange used to bolt directly to any manufacturer of Fans, as part of a full ancillary package or for the fan to mount inline in ducting.  ...

Back To Top